Maipu PU3200-1G1FN GPON HGU
Maipu PU3200-1G1FN GPON HGU is designed for fulfilling FTTH and triple play service demand of fixed network operators. These HGU adopt mature GPON technology, providing Wi-Fi, Layer 2/3 forwarding and rich management features as well. And they are fully compliant with technical regulations such as IEEE802.3ah, ITU-T G.984.x, etc.
PU3200-1G1FN provides 1*GPON port,1*GE Port,1*FE RJ45 Port and 802.11b/g/n Wi-Fi.
Product Features
Panel lights & Interface Description
LED | Mark | Status | Description |
Power | PWR | On | Device is powered up. |
Off | Device is powered down. | ||
Optical signal loss | LOS | Blink | Device does not receive optical signals. |
Off | Device has received optical signal. | ||
Registration | REG | On | Device is registered to the PON system. |
Off | Device is not registered to the PON system. | ||
Blink | Device is registering. | ||
Interface | GE、FE | On | Port is connected properly. |
Off | Port connection exception or not connected. | ||
Blink | Port is sending or/and receiving data. | ||
Wireless | Wi-Fi | On | Wi-Fi turned on. |
Off | Device is power off or Wi-Fi turned off. | ||
Blink | Wi-Fi data transmission. |
Port Type | Function |
PON | V2802W: SC/UPC type, single mode optical fiber cable V2802WT: SC/APC type, single mode optical fiber cable with WDM |
GE、FE | Connect device with ethernet port by RJ-45 cat5 cable. |
RST | Press down reset button and keep1-5seconds to make the device restart and recover from the factory default settings. |
DC12V | Connect with power adapter. |
Power On/OFF | Power turns on/off. |
Product Specifications
Hardware Specification | |
PON interface | 1 GPON Class B+ |
Receiving sensitivity: ≤-28dBm, Saturability: -8dBm | |
Transmitting optical power: 0~+4dBm | |
Transmission distance: 20KM | |
Wavelength | Tx1310nm,Rx 1490nm |
Optical interface | SC/UPC connector |
LAN interface | 1 x 10/100/1000Mbps and 1 x 10/100Mbps auto adaptive Ethernet interfaces. Full/Half, RJ45 connector |
Wi-Fi interface | Compliant with IEEE802.11b/g/n |
Operating frequency: 2.400-2.4835GHz | |
support MIMO, rate up to 300Mbps | |
2T2R,2 external antenna 5dBi | |
Support: multiple SSID | |
Channel:13 | |
Modulation type: DSSS、CCK and OFDM | |
Encoding scheme: BPSK、QPSK、16QAM and 64QAM | |
LED | For POWER, LOS, PON, GE, FE, Wi-Fi |
Operating condition | Temperature: 0℃～+50℃ |
Humidity: 10%～90%（non-condensing） | |
Storing | Temperature: -30℃～+70℃ |
condition | Humidity: 10%～90%（non-condensing） |
Power supply | DC 12V/1A |
Power supply | ≤6W |
Dimension | 185mm×120mm×34mm（L×W×H） |
Net weight | 0.24Kg |
Software Key Feature | |
Software mode | Bridging and Routing Mode |
Basic | Support MPCP discover and register |
Support authentication Mac/Loid/Mac+Loid | |
Support Triple Churning | |
Support DBA bandwidth | |
Support auto-detecting, auto-configuration, and auto firmware upgrade | |
Support authentication SN/Psw/Loid/Loid+Psw | |
Alarm | Support Dying Gasp |
Support Port Loop Detect | |
Support Eth Port Los | |
LAN | Support Loop Detection |
Support Storm Control | |
VLAN | Support 4K VLAN |
Support VLAN Tag/untag | |
Support VLAN Translation | |
Support VLAN Bound | |
Support Auto VLAN Detection | |
Multicast | Support IGMPv1/v2 |
Support IGMP Snooping | |
Support MLD | |
Max Multicast Group 64 | |
QoS | Support 4 queues |
Support SP and WRR | |
Support 802.1P | |
L3 | Support DHCP/PPPOE/Static IP |
Support NAT | |
Support IPv4 Static route | |
Support IPv4 dual stack | |
Wi-Fi | IEEE802.11b/g/n (TX power:17dBm/16dBm/15dBm), Up to 300Mbps |
Support Authentication: WEP/WAP-PSK(TKIP)/WAP2-PSK(AES) | |
Support multiple SSID and SSID conceal | |
Support Wireless channel selection | |
Management | Support CTC OAM 2.1 and 3.0 |
Support ITUT984.x OMCI | |
Support WEB | |
Support Telnet | |
Support CLI | |
Order Information
Product model | Product specification |
PU3200-1G1FN | GPON ONU, 1*GPON Port, 1*GE Port, 1*FE Port and 802.11b/g/n Wi-Fi |